Power Assist and Low Energy Power Operated Doors

A156.19 Low Energy Doors Detex

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2013

Keywords:
A156.19-2013, Power Assist, Low Energy Doors, Detex, A156.19

Company:
Detex Corporation
Visit Website

Product Line: 
Power Assist and Low Energy Power Operated Doors
Updated: 
Tue, 01/03/2017
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

A156.19 BEST Access Solutions, Inc.

New Search

Contact:
bstrong@stanleyworks.com
317-849-2250

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2013

Keywords:
A156.19, Low Energy Operated Doors, BEST Access Solutions

Company:
BEST Access Solutions, Inc.
Visit Website

Product Line: 
Power Assist and Low Energy Power Operated Doors
Updated: 
Fri, 04/21/2017
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

ANSI/BHMA A156.19 DORMA USA

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2013

Keywords:
POWER ASSIST AND LOW ENERGY, POWER OPERATED, A156.19-2013, A156.19, DORMA USA

Company:
DORMA USA
Visit Website

Product Line: 
Power Assist and Low Energy Power Operated Doors
Updated: 
Mon, 07/31/2017
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

ANSI/BHMA A156.19 POWER ASSIST AND LOW ENERGY POWER OPERATED DOORS

$18.00

Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

$18.00
Category: 
Power Assist and Low Energy Power Operated Doors

A156.19 Stanley Access Technologies

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2013

Keywords:
Power Assist & Low Energy Power Operated Doors, A156.19, 2007

Company:
Stanley Access Technologies

Product Line: 
Power Assist and Low Energy Power Operated Doors
Updated: 
Fri, 12/19/2014
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

A156.19 Sargent Manufacturing Company

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2007

Keywords:
Power Assist & Low Energy Power Operated Doors, A156.19, 2007

Company:
Sargent, an ASSA ABLOY Group brand
Visit Website

Product Line: 
Power Assist and Low Energy Power Operated Doors
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

A156.19 Norton Door Controls

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2013

Keywords:
Power Assist & Low Energy Power Operated Doors, A156.19, 2013

Company:
Norton, an ASSA ABLOY Group brand

Product Line: 
Power Assist and Low Energy Power Operated Doors
Updated: 
Fri, 07/28/2017
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

ANSI/BHMA A156.19 Power Assist and low Energy Doors LCN, Allegion

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Publication Year:
2007

Keywords:
Power Assist & Low Energy Power Operated Doors, A156.19, 2007

Company:
LCN, Allegion

Product Line: 
Power Assist and Low Energy Power Operated Doors
Updated: 
Thu, 01/30/2014
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

A156.19 Arrow Lock Manufacturing Company

New Search

Standard:
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors

Scope

ANSI/BHMA A156.19 - 2013 Power Assist & Low Energy Operated Doors

 

1.1 Requirements in this Standard apply only to swing door operators. The operator types are power assist, and low energy power operators, for pedestrian use, and some small vehicular use. It does not address doors, finish or hardware. The activation of all doors described in this standard requires a knowing act. Included are provisions intended to reduce the chance of user injury or entrapment.

1.2 Doors that require higher speeds, forces, shorter time delays, and activating sensing devices shall comply with ANSI/BHMA A156.10 for Power Operated Pedestrian Doors and are not covered in A156.19.

1.3 This Standard does not attempt to assess any factors that exist with respect to custom design installations which are not required to meet the requirements of this Standard.

1.4 Unless otherwise specified, all references to time delay, opening speed and forces in this standard, refer to the operator in the power mode as opposed to the manual mode.

1.5 Required dimensions are expressed in US units first and the SI (metric) equivalents given in parentheses are approximate. All values which do not carry specific tolerances or are not marked
maximum or minimum shall have the following tolerances: Linear dimensions shall be ± 1/16 in (1.6
mm). Pounds or pound force shall be ± 5%. Angular measurements shall be ± 4 degrees. Voltage
measurements shall be ± 5 percent. Temperature measurements shall be ± 4 degrees F (±2 degrees C).1.6 Compliance with the requirements of this standard shall be accomplished through factory settings or field adjustments as necessary.

1.7 Operators used on labeled fire door assemblies shall be listed or labeled by a nationally recognized independent testing laboratory, and be subject to a periodic in-plant follow-up service. Consult the authority having jurisdiction for the appropriate fire test requirements

Keywords:
Power Assist & Low Energy Power Operated Doors, A156.19, 2007

Company:
Arrow, an ASSA ABLOY Group brand
Visit Website

Product Line: 
Power Assist and Low Energy Power Operated Doors
ANSI/BHMA A156.19 Power Assist & Low Energy Power Operated Doors
Syndicate content